Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Brembo pad pin kit for Brembo P4 30/34F calipers fitted to front forks, two pins

Brembo ref. 120394230

 1 in stock

 01659130 GU01659130 01 65 91 30
 0165 9130 0165.9130 01.65.91.30

Brembo PS 13 handlebar mounted front master cylinder. The PS13 has a small rectangular fluid reservoir

Replaces Guzzi refs 28660178 and 30660180. Supplied complete with black or polished lever. Uses switch ELA30860

 1 in stock

 28660278 GU28660278 28 66 02 78
 2866 0278 2866.0278 28.66.02.78

Front brake master cylinder cap and rubber kit for Brembo PS 13 / PS16 master cylinder. Screw holes parallel to top and bottom edges

Brembo ref. 110430860

 1 in stock

Also fits Ducati 907 i.e.

Polished adjustable aluminium brake lever for PS 11, PS 13 and PS 16 master cylinders

Also known as Guzzi ref. 10270652. See HAA10850 for lever pivot pin and BRA01630 for span adjustable alternative lever

 1 in stock

30605680-z 30605680 GU30605680 30 60 56 80
 3060 5680 3060.5680 30.60.56.80

Polished replica adjustable aluminium brake lever for PS 16 and PS 22 handlebar master cylinders. Can also be fitted as an adjustable update to Breva 750, Nevada 750 (2004 on) , V7 Classic , V7 Cafe etc... Note that this lever blade is approximately 20mm shorter than the OE lever.

Also known as Guzzi ref. 981050 and 854603. BRA03645 can be used as a non adjustable substitute

 1 in stock

AP8133510

Also fits Aprilia Caponord, Aprilia Pegaso 650 (CHASSIS NUMBER PREFIX: ZD4VD0,ZD4VDA,ZD4VDB,ZD4VDD,ZD4VDE 2005-2009), Aprilia Futura 1000 (2001-2003)

Brakelight switch for handlebar mounted master cylinder

Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.

 1 in stock

 30749860 GU30749860 30 74 98 60
 3074 9860 3074.9860 30.74.98.60

Brake pad spring for single pin Brembo Goldline 30/34 calipers

Also suitable for some Ducati / Aprilia models. Brembo ref. 98.8248.50

 1 in stock

 20419685 GU20419685 20 41 96 85
 2041 9685 2041.9685 20.41.96.85

Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÃœV Rheinland.
  See BRA41652 for bleed valve cover

   1 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]